SoJ1RoTV 40,889 views 2:05 GM Turn Signal Problem Fix - Directional Relay Replacement - Duration: 5:38. Does anyone have any suggestions? 1993 Chevrolet Suburban K1500 4WD - Maintenance & Repair 2004 Tahoe Z71 brake lights not working. Clean them and use dielectric grease to seal them from moisture. If necessary, replace with a 4A fast-blow AGC type. http://dragonplayer.net/brake-light/brake-light-and-turn-signal-not-working-on-one-side.php
No bad wires when I took off the shielding. Close Yes, keep it Undo Close This video is unavailable. Any suggestions on next steps to fixing what I'm guessing is a voltage issue? The wiring diagram I cited was 2000, as that is the latest one I have printed out. http://www.agcoauto.com/content/news/p2_articleid/243
Louis janet8807 - September 16, 2013As a woman who has no clue about fixing a car, I find the articles here easy to understand. I cannot predict the future. Test the signal lights as described above - (No signal lights on either side.) Testing the connections from the dash to the bulb If you also have no parking lights at
I did a really simple test: I put in a new bulb, depressed the brake pedal for 10 seconds, and then compared the passenger side tail light to the problematic drivers louis - September 16, 2013Hi Janet, Thank you for your kind words. I really appreciate hearing that you like the site. One Brake Light Out With the pedal released, the brake-light switch should be pushed to its full off position.
You can only upload files of type PNG, JPG, or JPEG. One Brake Light Not Working Illegal The wire in question (feed to the passenger brake light) does not have any voltage, at lease at the bulb holder. __________________ 2001 XJ8 - L, Blue and Beautiful -Over 100,000 So I attempted to answer that question, and pointed out the inadvisability of doing so. http://www.bimmerforums.com/forum/showthread.php?1830798-Drivers-Side-brake-light-not-working-brake-pedal-switch I am not going to "rig" the third brake light to the pass rear brake.
If it does not, a problem exists with this circuit.With the brakes still applied, less than 0.1 volts should show on the black wire, when checked to the body ground. One Brake Light Not Working Bulb Ok Unusual brake light problem? 280zx Brake light issue!?!? If the bulb doesn't light, the bulb is bad, the socket isn't making contact, or the ground is bad. I am guessing my next step is to check the fuses?
If all lights come on, when the emergency flashers are turned on, this shows the bulbs, wires and sockets are good. Also, when I replaced the bulb, I also replaced a fuse labeled "back-up light". Brake Light Not Working But Tail Light Works To reverse the contact plate for the rear round parking lights with staggered pin bulbs (You can simply reverse the leads on the rear rectangular lights): Remove the lense and the Brake Light Doesn't Work But Tail Light Does A quick test is to try the emergency-flashers, on vehicles that use the brake lights as flashers. On vehicles where the flashers are separate from the brake lights, this will not
Expand» Details Details Existing questions More Tell us some more Upload in Progress Upload failed. get redirected here heeeheee View Public Profile Send a private message to heeeheee Find all posts by heeeheee #10 12-03-2014, 06:54 AM JennaNB1979 New Member Join Date: Dec 2014 I have Sign up here Find a Professional Type of Job Type of Job Additions and Remodels Appraisers and Home Inspectors Architects Bathroom Remodeling Cabinets and Countertops Carpentry Carpet Cleaning Concrete and Masonry Any clue what might fix this problem? One Brake Light Not Working But Bulb Is Good
To find exactly where it breaks, look at where it bends and flexes. When we use the turn signal switch, it cancels the brake light signal, on the side selected. If you were having a break in the connections anywhere, I would start there first, the trunk has a bundle of wires on the drivers side where the hinge is, unwrap navigate to this website Check the front signal lights. (Sometimes the a bad front light will prevent the rear from working.) If the signal switch works, replace the signal(trailer) relay.
TIA, Rich M3 Sedan Club President #21 Reply With Quote 05-03-2012,02:51 AM #2 ponchiz318 View Profile View Forum Posts Member Join Date Aug 2008 Location Houston, Tx. Brake Light Not Working But Bulb Ok Check the front signal light. (Sometimes the a bad front light will prevent the rear from working.) Switch the #7 yellow and #7 green wire where they go into the 4-way Press the brake pedal and they come on, release, and they go off.
Plus I dropped that nut that holds the tail light inside the trim, I cannot find or get it... I checked the fuses and they are good. The basic procedure is to start at one end of the circuit and check for voltage and ground. One Brake Light Not Working After Changing Bulb At the rear bulb socket, unplug both the red and yellow (or green) wires from their sockets, noting their respective locations.
If your bad side is still bad (the wand action will be reversed), the problem most likely the signal (trailer) relay. These are known for being a little loose. 2004NBTURBOS View Public Profile Send a private message to 2004NBTURBOS Find all posts by 2004NBTURBOS #3 04-08-2010, 03:55 PM adamhiggins New When the tail lights are on and I step on the brakes, the left tail light gets brighter, but the right one stays the same. my review here If memory serves, the one that says "BRAKE LIGHT CIRCUIT" is the brake light switch.
The time now is 06:19 PM. The cruise works as well. Pop the bulb back in and see what happens. __________________ The Mountains are calling and I must go. (John Muir) "May your dreams be larger then mountains and may you have If the bulb and connection are good, disconnect the pin junction to the rear harness at the left side of the dash.
these are push-in and turn bulbs? 1156 &1157? Answer Questions What's the difference between torque wrenches and torx wrenches? Turn on the parking lights. Advance Auto, Riley's etc.
Each rear light also has a separate fuse on a bracket underneath the steering column. Coopers Automotive Repair 2,229 views 17:32 Brake Light Switch removal testing and repair - Duration: 9:22.