Tech Forums •Technical Questions •Performance Modifications •General Discussion Classifieds •Cars For Sale •Used Parts For Sale Photos •BMW Events •Owner's Gallery Extras •2002 Sales Literature •Parts Catalog BMW Home> Technical I slid the red collar up and the switch can out without too much problem. September 10, 2009 Followup from the Pelican Staff: Thanks for the additonal info, very helpful. - Nick at Pelican Parts Craig Comments: Installation notes 1 The wiring connector has Category Autos & Vehicles License Standard YouTube License Show more Show less Loading... http://dragonplayer.net/brake-light/brake-rear-lights-not-working.php
Railfan2103 12,012 views 1:33 How to open brake light switch casing BMW E36 - Duration: 1:49. Glad it worked out.- Nick at Pelican Parts Lag Comments: Just did this on my car.... I have aftermarket red/clear tail lights. May 8, 2016 Followup from the Pelican Staff: The procedure should be similar on auto and manual trans models. http://www.bimmerforums.com/forum/showthread.php?1689206-Both-brake-lights-not-working
Sign in to make your opinion count. Forced Induction Automotive / Photography Car Navigation, Audio & Electronics by BAVSOUND The MINI Board Classifieds Cars - Private To do this, break the retaining tabs (green arrows) using a small flathead screwdriver, and then slide the switch out of the bracket.
This is a VERY easy problem to diagnose and fix. -Chris My e30 build thread/color change here Reply With Quote 07-27-2011,03:48 PM #6 pdfuentes View Profile View Forum Posts Member Join I also think there is a short for the passenger footwell light, it stays on forever, so I just took the bulb out because it was getting hot, do you by Second questions is can all the brake lights burn out at once? Bmw E36 Brake Light Bulb Brian Ripley 224,020 views 4:11 BMW E36 M3 brake light switch replacement - Duration: 5:43.
Brian Ripley 224,020 views 4:11 1995 Beloved BMW 325i project car for sale - Duration: 2:31. Bmw E36 Brake Light Fuse Location Parts have to stay secure and last, that is to blame. The bracket seemed to give a lot as I was trying to pull it out and was afraid the bracket would bend, so I used a screwdriver to break the tabs
froggy 17,336 views 8:48 Diagnosing Bad Brake Light Switch on your E36 BMW (Brake Light Circuit Error) - Duration: 3:50.
September 5, 2014 Followup from the Pelican Staff: COuld be the brake warning circuit, the bulbs or the sockets. E36 Brake Light Failure Powered by vBulletin® Version 4.1.8 Copyright © 2016 vBulletin Solutions, Inc. But once it extended it was easy to push in the retainers and pop out the switch. Could replacing this switch fix this error or does the working brake lights rule out this switch as the reason for the error message? 98 M3 March 25, 2012 Followup
Watch QueueQueueWatch QueueQueue Remove allDisconnect Loading...
Tech Forums • Technical Questions • Performance Modifications • General Discussion Extras • Cars For Sale • Used Parts For Sale • BMW Events • Parts Catalog BMW Home> BMW Bmw E36 Brake Light Switch Just keep it in drive until you get it in your driveway." i think the new switch may be bad... E36 Brake Light Circuit Failure And thank you very much for putting the article up in the first place : October 5, 2009 Followup from the Pelican Staff: There are many ways to remove the
done! More about the author Loading... Thanks, Reply With Quote 07-27-2011,03:53 PM #7 ajames View Profile View Forum Posts Member Join Date Jun 2004 Location Lancaster, PA Posts 413 My Cars '07 328xi 6MT IIRC, a bad Coastal Motor Works 1,948 views 2:00 BMW E36 M3 brake light switch replacement - Duration: 5:43. Bmw E36 Brake Light Circuit Warning
KUSTOMBLACK GUNZ 127,026 views 4:16 BMW E36 Replacing Instrument Cluster Bulbs - Duration: 4:12. Brake Light Circuit Bmw 325i Large Image | Extra-Large Image Figure 10 Replacing brake light switch-To install the new switch, press it into the bracket until the retaining tabs snap into place. After 1 mile the Brake light circuit light came on again.
as in no headlights on, the brake lights dont turn on or just the running lights? It's the rater large switch assembly that moves in conjunction with the brake pedal. used a fused jumper wire to battery positive. E36 Brake Light Switch 2-pin Or 4-pin Close Yeah, keep it Undo Close This video is unavailable.
So where is the wiring located and what exactly should I look for/replace? @Bianca98 - All 3 brake lights don't work 100% of the time. Dempsey Time: 30 minutes30 mins Tab: $9-$35 Talent: * Tools: Philips head screwdriver, plastic trim pry tool Applicable Models: BMW E30 3-Series (1984-93) BMW E36 3-Series (1992-99) Parts Required: Brake All is well and dandy again Cheers guys!!! http://dragonplayer.net/brake-light/brake-lights-and-rear-turn-signals-not-working.php Any suggestions would help!
If you do so you will find its almost impossible to install the new switch unless you remove the bracket it's mounted with just one ten millimeter bolt. Jennies Garage 341,164 views 4:03 Brake Light Switch removal testing and repair - Duration: 9:22. July 8, 2011 Followup from the Pelican Staff: On your model, all the rear brake lights run through the light check relay. I think John has a good point about the E36 tailights.
Published on Apr 20, 2013Weird problem. So I'd say it's probably the wiring. It's possible, but extremely unlikely, that all three brake lights will burn out at the same time. -Chris My e30 build thread/color change here Reply With Quote 08-03-2011,08:08 PM #9 guitarboy91 See The Official Book Website for more details.
johnnyBgood is offline Quote post #9 of 12 (permalink) Old 06-14-2010, 12:39 AM Thread Starter kholt n00b Join Date: Oct 2005 Posts: 33 Mentioned: 0 Post(s) Tagged: 0 Thread(s) I've just change one and the secret was to let the engine run and then push the brake pedeal as far as possible. Daniel House 52,244 views 8:08 Fixing a License Plate Light On a BMW - Duration: 4:28. Test the brake lights to make sure that they are working properly, and then reinstall the knee panel.
collar then pops out and the tabs can easily be squeezed with your fingers and the part slips out.