I have now driven 250 miles without the advisory lights on the dash so I'm thinking one or a combination of the above must have done some good. This brake pressure sensor has three pins (a) power, (b) ground and (c) the 0-5 volt proportionate signal. View My Garage No idea why you went through all those steps...all you had to do was have the car scanned and pull the code to find the problem... __________________ Have About 10 miles after leaving the garage I purchased the car from, my DSC and Brake lights came on in yellow accompanied by the warning tone.
Two days later the car is finally ready to be picked up. The signal is generated by a pulse wheel affecting the voltage flow through the hall element in the sensor. And could possibly save you some money. If it was your wheel speed sensors, I would think you would have the yellow traction lights on. __________________ Levim9 View Public Profile Find more threads by Levim9 Find More
Also, upgraded my car to xenon (actually it was factory xenon but they were removed). Thread Tools Show Printable Version 12-28-2010,01:56 PM #1 NoTempoLimit View Profile View Forum Posts Autobahn spezialist Join Date Aug 2010 Location Beverly Hills, CA Posts 308 My Cars 2009 E92 335i Ads by Google Guests, get your FREE E46Fanatics.com membership to remove this ad. Second issue I had was with the bluetooth, more specifically I could get my HTC Desire HD to pair with the system by following the process in the book. (hold down
ElectricRed46 View Public Profile Find more threads by ElectricRed46 Find More Posts by ElectricRed46 Leave feedback for ElectricRed46 (0) 11-28-2010, 11:05 PM #2 woopaul5 Registered User Join Date: May dreyo27 View Public Profile Find more threads by dreyo27 Find More Posts by dreyo27 Leave feedback for dreyo27 (0) 11-28-2010, 11:35 PM #4 iansanderson Registered User Join Date: Feb I'm not worried about driving without DSC, as I won't be going through snow, but the bright orange light is quite annoying on a dark night drive. Bmw E46 Dsc Light On Why I have no idea...anyway seems like loads of these control units fail after 6-7-8+ years of use. --D draja View Public Profile Find more threads by draja Find More
This was annoying. Bmw E46 Dsc Pressure Sensor Fault Then you have to code the control unit, and have the proper software to cycle the pump to properly bleed the brakes. Your car may need to adapt to the new height woopaul5 View Public Profile Find more threads by woopaul5 Find More Posts by woopaul5 Leave feedback for woopaul5 (0) 11-28-2010, http://forum.e46fanatics.com/showthread.php?t=842614 Posts: 6,608 My Ride: .
UNDERSTAND DIGITAL MULTIMETER (DMM) TEST BASICS: - http://www.allaboutcircuits.com/vol_3/chpt_3/2.html GATHER SEAT-OF-THE-PANTS DATA: - Note exactly which warning indicators are lit (e.g., ABS & BRAKE & DSC) - Note whether cruise control is Dsc Sensor Bmw E46 General E46 Forum This is the place to get answers, opinions and everything you need related to your E46 (sedan, coupe, convertible and wagon) BMW! You may have to register before you can post: click the register link above to proceed. READ THE SHOP MANUAL: ( http://www.bentleypublishers.com/isb...179/index.html ) - For DSC pinouts, see Volume II, page ELE-15 of ABS/DSC controle module (A65) (2 sensors in the front and 2 in the rear)
He called back a few hours later to say that the hydro unit had failed and needed to be replaced. http://www.bimmerfest.com/forums/showthread.php?t=525017 Damaged or missing teeth on the sensor ring will show up as flat spots or gaps in the sine wave pattern. Bmw E46 Dsc Light Reset Plus I like to fix anything that breaks. Bmw E46 Dsc Light Stays On Note: ASC cars have only two sensors, one on the front right and the other on the rear left wheel.
Anyway, it was sorted finally and didnt cost me anything so all is good. Home Classifieds Vendors Vendor Specials Store Rules Advertising Advanced Search Forum BMW Models 5 Series (E12, E28, E34, E39, E60, E61) 1996 - 2003 (E39) DSC Light On - How to Total cost £327. When the car had time to sufficiently cool, like the next day, the process would repeat itself. Bmw E46 Dsc And Brake Warning Light
Note: By way of comparison, the Corvette also has a brake pressure sensor to indicate how hard the brakes are being applied; it monitors pressure from 0 to 2000psi generating a E46Fanatics is the premiere website for BMW 3 series owners around the world with interactive forums, a geographical enthusiast directory, photo galleries, and technical information for BMW enthusiasts. Registration is fast, simple and absolutely free so please, join our community today! Worth a shot!
TEST STEERING ANGLE SENSOR: - We don't yet know how to test the steering-angle sensor (please advise) Note: The steering angle sensor, mounted at the bottom of the steering column near Bmw E46 Dsc And Handbrake Light Sent from my DROIDX using BimmerApp __________________ 1995 325i 5mt ArcticGrey/Dove - SOLD 2004 330ci ZHP 6MT SilberGrau/Black - SOLD 2001 330i M-Sport 5MT StaulGrau/Grey - SOLD 1992 Accord LX Sedan I'm going to try to take apart the old control unit to see if there is anything obvious...the teves mk60 unit in my 330 is not rebuildable by modulemasters.
The warning triangle just stays off? TORQUE TABLE: - 4mm wheel sensor bolts (two each for the front sensors, 1 each for the rear sensors) = 6 foot pounds - Combination lateral acceleration/rotational rate sensor (under driver DSC is still on but when I press the button it doesnt do anything, Ive even pressed and held it for about a minute and still nothing. E46 Dsc Button Not Working Using Hella ballasts, Phillps D2S bulbs, DJ Auto clusters with Umnitza angel eyes (Orion LED version), and Bi-Xenon low beam.
While lights were out I was able to turn DSC off, and back on again, and see the system working. - Clean wheel speed sensors - I didn't do this as Once I'd done this and after turning the engine off and restarting, magically the lights went out, at the very same second I thought "GREAT!" the lights came back on... - To start viewing messages, select the forum that you want to visit from the selection below. STEERING ANGLE SENSOR: REMOVE ABS MODULE: - Remove the six T20 Torx screws holding the ABS module to the hydro unit - Pull the ABS module straight out towards the passenger
TEST WHEEL SENSOR CIRCUIT FROM THE ABS CONNECTOR (also checks wiring circuit): OPTIONAL: Jack car up (so that all four wheels can be spun to test voltage & resistance fluctuations of Removing the previous phone book was simple, put the car into bluetooth paring mode, then hold the bluetooth button down until you hear a beep and the words RESET will appear I tried and failed to get any of my contacts to send, even once the phone was pared to the system, but as soon as BT paring mode was activated I User Name Remember Me?